IMPORTANT PRE-INSTALLATION NOTICE:

Before commencing the installation process, we strongly urge users to check the local laws thoroughly review this installation procedure and assess the time, knowledge, and resources needed to successfully complete it. PLEASE ALSO REVIEW THE DISCLAIMER AT THE END OF THIS INSTALLATION GUIDE.

While GLOSHOPfx’s kit offers a relatively straightforward connection, a fundamental understanding of the car's electrical system and a certain level of physical fitness are prerequisites.

It is highly recommended that the installation should be completed in one continuous session, as driving the car with an incomplete installation is not advisable. You may take short breaks if needed, but DO NOT OPERATE THE VEHICLE WITH AN UNFINISHED INSTALLATION. We recommend ensuring that all necessary components and tools are readily available before embarking on the installation journey.

Typically, the entire installation process may span from 3 to 6 hours or it may even take longer, depending on the car's make and model and the user's level of knowledge and expertise. If you choose not to undertake the kit installation by yourself, we recommend seeking the assistance of a professional service provider. The Edifier Inc. team, based in Toronto West, boasts extensive experience in installing similar kits and is more than willing to assist you in installing your underglow kit promptly and affordably. Please call them at (416) 766-2626 for appointment.

DOWNLOAD THE INSTALLATION GUIDE

Disclaimer

User acknowledges and assumes all risks associated with kit installation. GLOSHOPfx, its affiliates, owners, and staff are not liable for issues, guidance errors, or misunderstandings during installation. The user is solely responsible for any resulting consequences. GLOSHOPfx and affiliates are not liable for issues, damages, or injuries during or after kit installation by the user or related parties.

Begin the installation:

Before embarking on the installation process, prioritize safety by turning off the car engine, and ensuring the car's electrical system is off. It is recommended to take battery’s ground terminal off from the battery.

Step 1: Familiarizing yourself with the kit's contents:
  • 2x Front LED strips (80/90/100 cm each)
  • 2x Side LED strips (160/180/200 cm each)
  • 2x Rear LED strips (60CM/23.6” each)
  • 2x Extension cables (123CM/48” each)
  • 4x Connecting cables (246CM/96” each)
  • 1x Controller with necessary wires
  • 1x Absolute Power Cutoff Remote controller
  • Zip ties, clips, heat shrinkable tubes screws.
  • 6 ft GLOSHIELD L shaped black silicon strip.
  • A medium screw driver & wire cutter.
Gather the necessary tools for a smooth installation:
  • Phillips screwdriver (included in the kit)
  • Wire stripper (optional)
  • Cutter (included in the kit)
  • Scissor (optional)
  • Voltage tester or multimeter (optional)
  • Heat gun for heating the LED strip adhesive
  • Safety gloves
  • Safety glasses

Step 2: Testing the Kit:

Set your vehicle on a clean, dry, and safe surface, preferably having some extra space in front of your car for easy LED strip testing.

  • Connect the red wire from the power cable (equipped with a 10Amp fuse) to the positive power terminal in the fuse box located somewhere in the engine bay.
  • Ground the black wire from the power cable to a suitable grounding point within the vehicle.
    (Note: Avoid direct battery connection unless necessary, as it bypasses built-in safety features.)
  • Connect the extension cable’s one end with 3pin N16 male connector to the one of two cables coming out from the controller.
  • Connect one end of the front LED strip to the other end of the extension cable. GLOSHOPFX KIT INSTALLATION PROCEDURE 3
  • Attach the other end of the front LED strip’s female connector to the male connectors of a side LED strip.
  • Attach the other end of the side LED strip’s female connector to the male connector of rear LED strip.
  • Repeat this process for the other side by connecting the extension cable and other 3 LED strips with the 2nd cable coming out from the controller. Please note that at this moment we could test the kit without using extension cables. However, we recommended to test the extension cables as well.
  • Double check all the connectors as per the instruction above, and connect the ground battery connector, which we removed earlier, back on to the battery.
  • Now press the ON button on the power cutoff remote controller.

The LED lights should now illuminate. If not, press the power/ON button on the remote controller. This is the time to download the mobile app. The QR code for the mobile app is here: You might need to setup your mobile app as per the following procedure before you can utilize it or to test various colors and lighting patterns.

This would be a good time to install the Magic-LED app and familiarize yourself with a flood or colors you are about to add to your car. For installing the app please use the QR code provided in the installation guide or elsewhere in the kit.

Step 3: Preparing for Installation:

  • Disconnect the car battery negative or ground terminal once again. Disconnect all the LED strips from each other. You can keep the GLOSHOPfx’S power cables alongwith the controller connected.
  • Locate a suitable position to secure the controller. Ideally, try to find an existing mounting point where you can install the controller using screws. However, if this is not feasible, identify a secure location ensuring the controller is not in close proximity to moving parts and does not obstruct access to critical or frequently accessed areas. Optimal placement is on the rear or sides of the engine bay. Avoid fixing it onto moving parts, hose pipes, or the front near the radiator. In cases where screw installation is not possible, utilize zip ties to firmly position the controller. The black sleeve on the wires connected to the controller is a specially designed, fireresistant, and heat-resistant glass fiber tube, capable of withstanding temperatures up to 200°C. Do not remove it, as it serves to protect the wires from potential damage, even if they come into contact with hot surfaces in the engine bay.
  • Elevate your vehicle using suitable ramps or lifts, or be prepared to work safely beneath theLocate a suitable position to secure the Ideally, try to find an existing mounting point where you can install the controller using screws. However, if this is not feasible, identify a secure location ensuring the controller is not in close proximity to moving parts and does not obstruct access to critical or frequently accessed areas. Optimal placement is on the rear or sides of the engine bay. Avoid fixing it onto moving parts, hose pipes, or the front near the radiator. In cases where screw installation is not possible, utilize zip ties to firmly position the controller. The black sleeve on the wires connected to the controller is a specially designed, fire- resistant, and heat-resistant glass fiber tube, capable of withstanding temperatures up to 200°C. Do not remove it, as it serves to protect the wires from potential damage, even if they come into contact with hot surfaces in the engine bay.
  • Keep two extension wires connected to the two cables emerging from the controller. Route the cables to the lower side of the car, avoiding moving components, belts, pulleys, and hot surfaces.
  • Elevate your vehicle using suitable ramps or lifts, or be prepared to work safely beneath the car

Step 4: Installing the LED Strips

Start with the front LED strip installation:

  • Position one end of the front strip in the exact middle of the car's front side, underneath the vehicle.
  • Gently guide the other side of the Front LED strip toward the right side of the car's front, shaping it to fit the car's curved body.
  • LED strips are flexible and can bend up to 10-25 degrees, depending on the curve's length.
  • Thoroughly clean the selected surface with an alcohol-based cleaner, ensuring it is free from dust and grease.
  • Remove the protective plastic from the sticky side of the LED strip and carefully apply it to the cleaned area under the car's body.
  • Before applying the LED strip to the designated place, it is recommended to use a heat gun or cigarette lighter to lightly heat the sticky side of the LED strip.
  • After successfully affixing the LED strip beneath the car body to its full extent, secure the strip in place using the provided clips and screws. The kit includes 40 clips, consisting of 20 clips each measuring 12mm and 14mm. In certain areas, external methods may be necessary to conceal or hide the LED strips effectively. GLOSHOPfx kits are equipped with 6 feet of GloShield silicon L-shaped strips, tailor-made for this purpose. Opt for the 12mm clips where GloShield is not used.
  • However, when employing the GloShield LED strip hiding silicon strip, utilize the 14mm clips. The clips, crafted from flexible yet sturdy plastic, exhibit an interesting phenomenon – if installed directly above the LED bead, they may act as reflectors and emit a glow in the dark. To mitigate this effect, consider using 10mm diameter heat-shrinkable tubes. The kit provides 15 heat shrink tubes tailored to the GLOSHOPFX KIT INSTALLATION PROCEDURE 5 required size. Simply slide the 14mm clip into the heat shrink tube, secure it with a tweezer or plier, and apply heat using a heat gun. Once the tube shrinks, the clip will be entirely covered with the opaque black heat shrink, preventing it from illuminating in the dark.

Repeat the above process for the side and rear LED strips. Exercise caution when installing the rear LED strips to avoid contact with the car's exhaust system. Ensure that the LED strips are discreetly placed to only reveal the glowing effect on the ground. Use gloshield black silicon hiding strip where it is deemed necessary. You can always order for extra length of GLOSHIELD hiding strip and extra clips from our webstore gloshopfx.com

Step 5: Connecting the Strips Together
  • Determine the best point in the installation process to connect the cables between the controller, front strip, and subsequent strips based on your vehicle's make and model. Ideally, make these connections just after adhering the strips to the car's surface. And after securing them with the provided clips.
  • Bundle any excess wire length and secure it with provided zip ties.
  • Conceal the wire bundle beneath the car's body, taking care to prevent it from making contact with the ground or any moving components.
  • Double check if all are properly connected and secured.
Step 6: Connecting the power:
  • Get back to the engine bay.
  • Connect the car battery negative terminal to the battery, turn the GLOSHOPfx underglow controller ON by pressing “ON” on the provided remote controller.
  • Use the mobile app to select your favorite color and the flow pattern.
  • Your GLOSHOPfx Car Underglow Kit is now expertly installed, enhancing your vehicle's aesthetics with striking LED lighting while prioritizing safety and preserving your car's battery. Enjoy the mesmerizing glow as you hit the road! Enjoy!

Troubleshooting/FAQs:

  • Extended length options for comprehensive coverage
  • Professional-grade materials for durability
  • Easy installation with included mounting hardware
  • High-intensity LEDs for maximum visibility
  • Even light distribution across entire length
  • Advanced heat management for consistent performance
  • Cut-to-length capability for custom installations
  • Modular design for flexible configurations
  • Perfect fit for any vehicle size or type
  • Over 200 lighting patterns, including flowing, pulsing, and strobe effects.
  • 16.7 million color combinations for endless customization.
  • Advanced Flow-Control Patterns create eye-catching ambient effects.
  • Plug-and-play setup with detailed instructions
  • Universal mounting brackets included
  • No special tools or expertise required
  • Compatible with most vehicle makes and models
  • Standard 12V DC power connection
  • Works with existing electrical systems
  • Smartphone app for complete control
  • Physical remote control included
  • Voice control compatibility with smart assistants

Remember that if you encounter any issues or are unsure about any step of the installation process, it's advisable to seek professional assistance or contact GLOSHOPfx's customer support for guidance.

Even though our GLOSHOPfx underglow kit is user-friendly for installation, we want to ensure that you have options that best suit your needs. If you choose not to install it yourself or simply prefer the expertise of our team, we offer discounted professional installation services for our customers who bought underglow kit. Our dedicated team is ready and excited to assist you in bringing the magic of our underglow kit to your vehicle. Your satisfaction is our priority.

Notice of Product Usage Restrictions and Disclaimers:

Certain products offered by us are intended exclusively for OFF-ROAD USE ONLY. We strongly advise you to consult with your local highway patrol or Department or Ministry of Transportation or Motor Vehicles (whatever it is referred to locally) to ascertain and adhere to pertinent rules, regulations, and information applicable to such products. GLOSHOPfx assumes no responsibility for any legal implications arising from the purchase of products from our establishment. We hereby assert our prerogative, without incurring liability or furnishing prior notice, to amend, discontinue, or withdraw from circulation any or all of our products, as well as to decline or revoke any orders.

While GLOSHOPfx endeavors to uphold the precision of product information, we disclaim liability for any typographical, photographic, or technical inaccuracies. By making a purchase of our product, the buyer hereby implicitly acknowledges and consents to adhere to the terms and conditions outlined by our company.